This is Gentoo's testing wiki. It is a non-operational environment and its textual content is outdated.
Please visit our production wiki at https://wiki.gentoo.org
Embedded Handbook/Boards/Hammer Board and Nail Board
From Gentoo Wiki (test)
< Embedded Handbook | Boards
Jump to:navigation
Jump to:search
Little-endian armv4l board.
Nail Board specifications
Board specifications:
CODE
# All power received from the USB port (no external power supply required)
# Male (upstream) USB connector
# Female (downstream) USB connector
# Complete USB JTAG device on board (via internal FT2232)
# USB Hub on board
# USB serial port console (via internal FT2232)
# USB controlled GPIO's (for configuration)
# USB gadget interface (via the Hammer module)
* Ethernet Gadget Driver (default)
* Serial Port Gadget Driver
* Mass Storage Driver
# USB host interface (via the Hammer module)
* USB 1.1 Compliant
* Low Speed Support (2mb)
* Full Speed Support (12mb)
# 3 User LED's available
* Two on the Nail Board
* One user LED on the Hammer module
* USER led on the Hammer Board
# 2 interrupt driven pushbutton switches
# User controlled PWM buzzer
# Reset button
# Power LED
# Expansion header (20-pin: 2 x10)
* +5V available
* +3.3V available
* 2 SPI ports
* 2 wire Serial Port (TX/RX)
* GPIO's
* External Interrupts
* Headers can be jumper configured
# Hammer module breakout header
* Access to all 40 I/O pins of the Hammer module
* 0.1 inch headers/proc/cpuinfo
CPU info:
FILE
/proc/cpuinfoProcessor : ARM920T rev 0 (v4l) BogoMIPS : 101.17 Features : swp half thumb CPU implementer : 0x41 CPU architecture: 4T CPU variant : 0x1 CPU part : 0x920 CPU revision : 0 Cache type : write-back Cache clean : cp15 c7 ops Cache lockdown : format A Cache format : Harvard I size : 16384 I assoc : 64 I line length : 32 I sets : 8 D size : 16384 D assoc : 64 D line length : 32 D sets : 8 Hardware : TCT_HAMMER Revision : 0000 Serial : 0000000000000000
Cross compile preparation
Setup uClibc:
root #echo '>=cross-arm-softfloat-linux-uclibc/gcc-4' >> /etc/portage/package.mask
root #echo 'dev-embedded/openocd ft2232 ftdi' >> /etc/portage/package.use
root #modprobe ftdi_sio
root #emerge openocd
root #ACCEPT_KEYWORDS="~*" emerge crossdev
root #crossdev arm-softfloat-linux-uclibc
Setup uClibc and EABI:
root #echo '>=cross-armv4l-softfloat-linux-uclibceabi/gcc-4' >> /etc/portage/package.mask
root #echo 'dev-embedded/openocd ft2232 ftdi' >> /etc/portage/package.use
root #modprobe ftdi_sio
root #emerge openocd
root #ACCEPT_KEYWORDS="~*" emerge crossdev
root #crossdev armv4tl-softfloat-linux-uclibceabi
External resources
- TinCanTools
- TCT-Hammer Wiki
- Hammer Board
- Nail Board
- Default Kernel Config
- Nail Schematic
- (Gentoo Embedded) Reference Firmware
- (Gentoo Embedded) Reference Kernel Config
This page is based on a document formerly found on our main website gentoo.org.
The following people contributed to the original document: Mike Frysinger, Ned Ludd, Robin H. Johnson, Alex Tarkovsky, Alexey Shvetsov, Raúl Porcel, Joshua Saddler on April 28, 2013.
They are listed here because wiki history does not allow for any external attribution. If you edit the wiki article, please do not add yourself here; your contributions are recorded on each article's associated history page.