This is Gentoo's testing wiki. It is a non-operational environment and its textual content is outdated.
Please visit our production wiki at https://wiki.gentoo.org
ハンドブック:PPC64/インストール/ディスク
ブロックデバイスの概要
ブロックデバイス
Gentoo Linuxの、そしてLinux一般の、Linuxファイルシステム、パーティション、ブロックデバイスを含めた、ディスク中心の考え方について詳しく見てみましょう。ディスクの入出力とファイルシステムについて理解することで、Gentoo Linuxインストールのためのパーティションとファイルシステムを構築できるようになります。
まずはブロックデバイスについて見ていきます。最も有名なブロックデバイスはおそらく、Linuxシステム上で1番目のドライブを表す、/dev/sdaでしょう。SCSIとSerial ATAドライブは/dev/sd*と名付けられます。より新しいlibataフレームワークがカーネルに組み込まれていれば、IDEデバイスも/dev/sd*と名付けられます。古いデバイスフレームワークを使っていれば、1番目のIDEドライブは/dev/hdaになるでしょう。
上のブロックデバイスは、ディスクへの抽象的なインターフェースを表しています。ユーザープログラムはこれらのブロックデバイスを用いて、デバイスがIDE、SCSI、もしくは他のものであるかどうかを心配することなしにディスクと通信することができます。プログラムは容易にディスク上の記憶領域を、ランダムアクセスできる512バイトごとの連続領域としてアドレッシングできます。
Partitions and slices
Although it is theoretically possible to use a full disk to house a Linux system, this is almost never done in practice. Instead, full disk block devices are split up in smaller, more manageable block devices. On most systems, these are called partitions. Other architectures use a similar technique, called slices.
Designing a partition scheme
How many partitions and how big?
The number of partitions is highly dependent on the environment. For instance, if there are lots of users, then it is advised to have /home/ separate as it increases security and makes backups easier. If Gentoo is being installed to perform as a mail server, then /var/ should be separate as all mails are stored inside /var/. A good choice of filesystem will then maximize the performance. Game servers will have a separate /opt/ as most gaming servers are installed there. The reason is similar for the /home/ directory: security and backups. In most situations, /usr/ is to be kept big: not only will it contain the majority of applications, it typically also hosts the Gentoo ebuild repository (by default located at /usr/portage) which already takes around 650 MiB. This disk space estimate excludes the packages/ and distfiles/ directories that are generally stored within this ebuild repository.
It very much depends on what the administrator wants to achieve. Separate partitions or volumes have the following advantages:
- Choose the best performing filesystem for each partition or volume.
- The entire system cannot run out of free space if one defunct tool is continuously writing files to a partition or volume.
- If necessary, file system checks are reduced in time, as multiple checks can be done in parallel (although this advantage is more with multiple disks than it is with multiple partitions).
- Security can be enhanced by mounting some partitions or volumes read-only,
nosuid
(setuid bits are ignored),noexec
(executable bits are ignored) etc.
However, multiple partitions have disadvantages as well. If not configured properly, the system might have lots of free space on one partition and none on another. Another nuisance is that separate partitions - especially for important mount points like /usr/ or /var/ - often require the administrator to boot with an initramfs to mount the partition before other boot scripts start. This isn't always the case though, so results may vary.
There is also a 15-partition limit for SCSI and SATA unless the disk uses GPT labels.
What about swap space?
There is no perfect value for the swap partition. The purpose of swap space is to provide disk storage to the kernel when internal memory (RAM) is under pressure. A swap space allows for the kernel to move memory pages that are not likely to be accessed soon to disk (swap or page-out), freeing memory. Of course, if that memory is suddenly needed, these pages need to be put back in memory (page-in) which will take a while (as disks are very slow compared to internal memory).
When the system is not going to run memory intensive applications or the system has lots of memory available, then it probably does not need much swap space. However, swap space is also used to store the entire memory in case of hibernation. If the system is going to need hibernation, then a bigger swap space is necessary, often at least the amount of memory installed in the system.
Default: Using mac-fdisk
These instructions are for the Apple G5 system.
Start mac-fdisk:
root #
mac-fdisk /dev/sda
First delete the partitions that have been cleared previously to make room for Linux partitions. Use d in mac-fdisk to delete those partition(s). It will ask for the partition number to delete.
Second, create an Apple_Bootstrap partition by using b. It will ask what block to start from. Enter the number of the first free partition, followed by a p. For instance this is 2p.
This partition is not a "boot" partition. It is not used by Linux at all; there is no need to place any filesystem on it and it should never be mounted. PPC users don't need an extra partition for /boot.
Now create a swap partition by pressing c. Again mac-fdisk will ask what block to start from. As we used 2 before to create the Apple_Bootstrap partition, enter 3p. When asked for the size, enter 512M (or whatever size needed). When asked for a name, enter swap (mandatory).
To create the root partition, enter c, followed by 4p to select from what block the root partition should start. When asked for the size, enter 4p again. mac-fdisk will interpret this as "Use all available space". When asked for the name, enter root (mandatory).
To finish up, write the partition to the disk using w and q to quit mac-fdisk.
To make sure everything is ok, run mac-fdisk once more and check whether all the partitions are there. If not all created partitions are shown, or it is missing some of the changes that were made, then reinitialize the partitions by pressing i in mac-fdisk. Note that this will recreate the partition map and thus remove all the partitions.
代替案: fdisk を用いる
The following instructions are for IBM pSeries, iSeries, and OpenPower systems.
When planning to use a RAID disk array for the Gentoo installation on POWER5-based hardware, first run iprconfig to format the disks to Advanced Function format and create the disk array. Emerge sys-fs/iprutils after the installation is complete.
If the system has an ipr-based SCSI adapter, start the ipr utilities now.
root #
/etc/init.d/iprinit start
The following parts explain how to create the example partition layout described previously, namely:
Partition | Description |
---|---|
/dev/sda1 | PPC PReP Boot partition |
/dev/sda2 | Swap partition |
/dev/sda3 | Root partition |
Change the partition layout according to personal preference.
Viewing current partition layout
fdisk is a popular and powerful tool to split a disk into partitions. Fire up fdisk on the current disk (in our example, we use /dev/sda):
root #
fdisk /dev/sda
Command (m for help)
If there is still an AIX partition layout on the system, then the following error message will be displayed:
root #
fdisk /dev/sda
There is a valid AIX label on this disk. Unfortunately Linux cannot handle these disks at the moment. Nevertheless some advice: 1. fdisk will destroy its contents on write. 2. Be sure that this disk is NOT a still vital part of a volume group. (Otherwise you may erase the other disks as well, if unmirrored.) 3. Before deleting this physical volume be sure to remove the disk logically from your AIX machine. (Otherwise you become an AIXpert).
Don't worry, new empty DOS partition table can be created by pressing o.
This will destroy any installed AIX version!
Type p to display the disk current partition configuration:
Command (m for help):
p
Disk /dev/sda: 30.7 GB, 30750031872 bytes 141 heads, 63 sectors/track, 6761 cylinders Units = cylinders of 8883 * 512 = 4548096 bytes Device Boot Start End Blocks Id System /dev/sda1 1 12 53266+ 83 Linux /dev/sda2 13 233 981571+ 82 Linux swap /dev/sda3 234 674 1958701+ 83 Linux /dev/sda4 675 6761 27035410+ 5 Extended /dev/sda5 675 2874 9771268+ 83 Linux /dev/sda6 2875 2919 199836 83 Linux /dev/sda7 2920 3008 395262 83 Linux /dev/sda8 3009 6761 16668918 83 Linux
This particular disk is configured to house six Linux filesystems (each with a corresponding partition listed as "Linux") as well as a swap partition (listed as "Linux swap").
Removing all partitions
First remove all existing partitions from the disk. Type d to delete a partition. For instance, to delete an existing /dev/sda1:
Command (m for help):
d
Partition number (1-4): 1
The partition has been scheduled for deletion. It will no longer show up when typing p, but it will not be erased until the changes have been saved. If a mistake was made and the session needs to be aborted, then type q immediately and hit Enter and none of the partitions will be deleted or modified.
Now, assuming that indeed all partitions need to be wiped out, repeatedly type p to print out a partition listing and then type d and the number of the partition to delete it. Eventually, the partition table will show no more partitions:
Command (m for help):
p
Disk /dev/sda: 30.7 GB, 30750031872 bytes 141 heads, 63 sectors/track, 6761 cylinders Units = cylinders of 8883 * 512 = 4548096 bytes Device Boot Start End Blocks Id System
Now that the in-memory partition table is empty, let's create the partitions. We will use a default partitioning scheme as discussed previously. Of course, don't follow these instructions to the letter but adjust to personal preference.
Creating the PPC PReP boot partition
First create a small PReP boot partition. Type n to create a new partition, then p to select a primary partition, followed by 1 to select the first primary partition. When prompted for the first cylinder, hit Enter. When prompted for the last cylinder, type +7M to create a partition 7 MB in size. After this, type t to set the partition type, 1 to select the partition just created and then type in 41 to set the partition type to "PPC PReP Boot". Finally, mark the PReP partition as bootable.
The PReP partition has to be smaller than 8 MB!
Command (m for help):
p
Disk /dev/sda: 30.7 GB, 30750031872 bytes 141 heads, 63 sectors/track, 6761 cylinders Units = cylinders of 8883 * 512 = 4548096 bytes Device Boot Start End Blocks Id System
Command (m for help):
n
Command action e extended p primary partition (1-4) p Partition number (1-4): 1 First cylinder (1-6761, default 1): Using default value 1 Last cylinder or +size or +sizeM or +sizeK (1-6761, default 6761): +8M
Command (m for help):
t
Selected partition 1 Hex code (type L to list codes): 41 Changed system type of partition 1 to 41 (PPC PReP Boot)
Command (m for help):
a
Partition number (1-4): 1 Command (m for help):
Now, when looking at the partition table again (through p), the following partition information should be shown:
Command (m for help):
p
Disk /dev/sda: 30.7 GB, 30750031872 bytes 141 heads, 63 sectors/track, 6761 cylinders Units = cylinders of 8883 * 512 = 4548096 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 3 13293 41 PPC PReP Boot
スワップパーティションを作成する
Now create the swap partition. To do this, type n to create a new partition, then p to tell fdisk to create a primary partition. Then type 2 to create the second primary partition, /dev/sda2 in our case. When prompted for the first cylinder, hit Enter. When prompted for the last cylinder, type +512M to create a partition 512MB in size. After this, type t to set the partition type, 2 to select the partition just created and then type in 82 to set the partition type to "Linux Swap". After completing these steps, typing p should display a partition table that looks similar to this:
Command (m for help):
p
Disk /dev/sda: 30.7 GB, 30750031872 bytes 141 heads, 63 sectors/track, 6761 cylinders Units = cylinders of 8883 * 512 = 4548096 bytes Device Boot Start End Blocks Id System /dev/sda1 1 3 13293 41 PPC PReP Boot /dev/sda2 4 117 506331 82 Linux swap
ルートパーティションを作成する
Finally, create the root partition. To do this, type n to create a new partition, then p to tell fdisk to create a primary partition. Then type 3 to create the third primary partition, /dev/sda3 in our case. When prompted for the first cylinder, hit Enter. When prompted for the last cylinder, hit enter to create a partition that takes up the rest of the remaining space on the disk. After completing these steps, typing p should display a partition table that looks similar to this:
Command (m for help):
p
Disk /dev/sda: 30.7 GB, 30750031872 bytes 141 heads, 63 sectors/track, 6761 cylinders Units = cylinders of 8883 * 512 = 4548096 bytes Device Boot Start End Blocks Id System /dev/sda1 1 3 13293 41 PPC PReP Boot /dev/sda2 4 117 506331 82 Linux swap /dev/sda3 118 6761 29509326 83 Linux
パーティションのレイアウトを保存する
To save the partition layout and exit fdisk, type w.
Command (m for help):
w
ファイルシステムを作成する
はじめに
パーティションが作成できたら、その上にファイルシステムを作成します。次の節ではLinuxがサポートする各種ファイルシステムを紹介します。どのファイルシステムを使うかをすでに決めているなら、パーティションにファイルシステムを適用するへ進みましょう。そうでなければ、次の節を読んで利用可能なファイルシステムについて知るのがよいでしょう。
ファイルシステム
利用可能なファイルシステムは複数あります。そのうちいくつかはアーキテクチャppc64上で安定して動作するとされています--重要なパーティションに実験的なファイルシステムを選択するときは、事前にファイルシステムのサポート状況を十分に知っておくことを推奨します。
- btrfs
- スナップショット、チェックサムによる自己修復、透過的圧縮、サブボリューム、RAIDの統合など、多くの先進機能を提供する次世代のファイルシステムです。いくつかのディストリビューションはこれをすぐに使えるオプションとして提供し始めていますが、未だ製品に使える状態ではありません。ファイルシステムが壊れたという報告はよくあります。開発者はユーザーに、安全のため最新のカーネルバージョンを使うようしきりに促しています。古いカーネルには既知の問題があるからです。この状況は何年も続いており、事態が変わってきたと判断するには早すぎます。問題への修正が古いカーネルにバックポートされることは滅多にありません。このファイルシステムを使う際は十分注意を払うようにしてください。
- ext2
- 試練を受けた本当のLinuxファイルシステムですが、メタデータジャーナリングがないため、起動時に行われる毎回のext2ファイルシステムチェックは時間のかかるものになります。今ではジャーナルの効く新世代の、整合性を非常に素早くチェックできるファイルシステムの選択肢が数多くありますから、一般的にはそちらのほうが、ジャーナルの効かない対抗馬より好まれます。ジャーナルの効くファイルシステムは、システム起動の際たまたまファイルシステムに不整合があった場合の長い遅延を防いでくれます。
- ext3
- ジャーナルが有効になった ext2 ファイルシステムであり、full data及びordered dataジャーナリングといった強力なジャーナリングモードに加え、高速な修復のためのメタデータジャーナリングをサポートします。HTreeインデックスによって、ほぼすべての状況で高いパフォーマンスが可能になります。簡単にいえば、ext3 はとても優れた信頼できるファイルシステムです。
- ext4
- もともと ext3 のフォークとして作られた ext4 は、新機能、パフォーマンスの向上と、ディスク上でのフォーマットの適度な変更による、サイズ制限の撤廃を提供します。ボリュームは1EBまで広げることができ、最大のファイルサイズは16TBです。古典的なext2/3のbitmap block割当ての代わりに、ext4 はextentを使い、大きなファイルでのパフォーマンスを向上し、断片化を減らしています。ext4は他にもより洗練されたアロケーションアルゴリズム(遅延割当てと複数ブロック割当て)を提供し、ファイルシステムドライバーに、ディスク上のデータのレイアウトを最適化するより多くの方法を与えています。ext4 は推奨される、全目的、全プラットフォームのファイルシステムです。
- f2fs
- Flash-Friendly File Systemはもともと、SamsungによってNANDフラッシュメモリで利用するために作られました。2016年Q2現在、このファイルシステムはまだ未熟なものと思われますが、GentooをmicroSDカードやUSBスティックや他のフラッシュベースの記憶装置にインストールする際にはすばらしい選択でしょう。
- JFS
- IBMの高パフォーマンスジャーナリングファイルシステムです。JFSは軽量、高速かつ信頼できる、B+木ベースのファイルシステムで、様々な条件で良いパフォーマンスが出ます。
- ReiserFS
- B+木ベースのジャーナルが有効なファイルシステムで、全体的に良いパフォーマンスが出ます。特に、大量の小さなファイルを扱う際は、CPUサイクルを多く消費するものの、高いパフォーマンスを得ることができます。ReiserFSは他のファイルシステムと比べるとあまり保守されていないように思われます。
- XFS
- メタデータジャーナリングのあるファイルシステムで、堅牢な機能セットを持ち、スケーラビリティに最適化されています。XFSはどうやら、様々なハードウェアの問題に対してはあまり寛大ではないようです。
- vfat
- 別名FAT32。Linuxでサポートされていますが、いかなるパーミッションの設定もサポートされていません。ほとんど、他のOS(主にMicrosoft Windows)との相互運用性のために使われていますが、いくつかのシステムファームウェア(たとえばUEFI)でも必要になります。
- NTFS
- この "New Technology" ファイルシステムは、Microsoft Windowsのフラッグシップファイルシステムです。上記のvfatと同様、BSDやLinuxが正しく動作するために必要なパーミッション設定や拡張属性を保持しないため、ルートファイルシステムとして使うことはできません。Microsoft Windowsとの相互運用のためにのみ使うべきです(「のみ」の強調に注意してください)。
ext2、ext3、ext4を(8GB以下の)小さいパーティションに使用するときは、十分なinode数を確保できるように適切なオプションを指定してファイルシステムを作成する必要があります。mke2fs (mkfs.ext2)アプリケーションは、「inodeあたりのバイト数」を指定することで、ファイルシステムが持つべきinode数を計算することができます。もっと小さいパーティションでは、計算されたinode数よりも大きい値を設定するとよいでしょう。
ext2では、これは次のコマンドで実行できます:
root #
mkfs.ext2 -T small /dev/<device>
ext3とext4では、ジャーナリングを有効にするために-j
オプションを追加しましょう:
root #
mkfs.ext2 -j -T small /dev/<device>
上のコマンドは通常では、「inodeあたりのバイト数」を16kBから4kBに減らすので、ファイルシステムに4倍のinode数を確保できます。比率を指定することで、さらに細かく調節することもできます:
root #
mkfs.ext2 -i <ratio> /dev/<device>
パーティションにファイルシステムを適用する
パーティションまたはボリュームの上にファイルシステムを作成するには、ファイルシステムごとに異なるユーザースペースのユーティリティが利用可能です。下表でファイルシステムの名前をクリックすると、それぞれに追加の情報が得られます:
ファイルシステム | 作成コマンド | Minimal CD にある? | パッケージ |
---|---|---|---|
btrfs | mkfs.btrfs | はい | sys-fs/btrfs-progs |
ext2 | mkfs.ext2 | はい | sys-fs/e2fsprogs |
ext3 | mkfs.ext3 | はい | sys-fs/e2fsprogs |
ext4 | mkfs.ext4 | はい | sys-fs/e2fsprogs |
f2fs | mkfs.f2fs | はい | sys-fs/f2fs-tools |
jfs | mkfs.jfs | はい | sys-fs/jfsutils |
reiserfs | mkfs.reiserfs | はい | sys-fs/reiserfsprogs |
xfs | mkfs.xfs | はい | sys-fs/xfsprogs |
vfat | mkfs.vfat | はい | sys-fs/dosfstools |
NTFS | mkfs.ntfs | はい | sys-fs/ntfs3g |
例えば、パーティション構造例の通りに、ブートパーティション(/dev/sda1)をext2に、ルートパーティション(/dev/sda3)をext4に設定するには、次のコマンドが使えます:
root #
mkfs.ext2 /dev/sda1
root #
mkfs.ext4 /dev/sda3
それでは、新しく作成したパーティション(または論理ボリューム)にファイルシステムを作成しましょう。
スワップパーティションを有効にする
mkswapはスワップパーティションを初期化するために使われるコマンドです:
root #
mkswap /dev/sda2
スワップパーティションを有効化するには、swaponを使います:
root #
swapon /dev/sda2
上述のコマンドで、スワップを作成して有効化しましょう。
マウント
パーティションが初期化され、ファイルシステムを格納したので、それらのパーティションをマウントする時です。 mount コマンドを使用しますが、作成されたすべてのパーティションに必要なマウントディレクトリを作成することを忘れないでください。例として、 root と boot パーティションをマウントします。
root #
mount /dev/sda3 /mnt/gentoo
root #
mkdir /mnt/gentoo/boot
root #
mount /dev/sda1 /mnt/gentoo/boot
もし/tmp/を別のパーティションに置く必要があるなら、マウントしたあと権限の変更を忘れずに行ってください:
root #
chmod 1777 /mnt/gentoo/tmp
このあと解説の中で、proc ファイルシステム(仮想的なカーネルとのインターフェース)が、他のカーネル擬似ファイルシステムと同様にマウントされますが、まず最初は、Gentooインストールファイルをインストールします。